Shortinfo ADN, BAM no. 841 (DGG-Info)

DGG-Info

Datenbank GEFAHRGUT (DGG-Info)

DE/EN

Trichloroacetic acid, aqueous solution, corrosive

Seiten

Verkehrsträger/Vorschrift

Sprache

DE/EN

Drill letter 1
Drill number
Inherent hazard
Hazard to aircraft
Hazard to occupants
Spill or leak procedure
Firefighting procedure
Additional considerations
Drill letter 2

Shortinfo ADN 2025

BAM name (German)	Trichloressigsäure, wässerige Lösung, ätzend
BAM name (English)	Trichloroacetic acid, aqueous solution, corrosive
BAM name (French)	Acide trichloracétique, en solution aqueuse, corrosif
Aggregate state (under normal conditions)	liquid
BAM no.	841
CAS no.	(76-03-9)
Detailinfo

German	TRICHLORESSIGSÄURE, LÖSUNG
English	TRICHLOROACETIC ACID SOLUTION
French	ACIDE TRICHLORACÉTIQUE EN SOLUTION
Detailinfo

UN no.	2564
Class
Classification code
Packing group
Special provisions	none
Transport status in dry cargo vessels	allowed
Transport status in tank vessels	allowed
Detailinfo

Labels	Label 8 Class 8 hazard: Corrosive substances Label model No. 8 Symbol and symbol colour: Liquids, spilling from two glass vessels and attacking a hand and a metal, black Background: Upper half white, lower half black with white border Figure in bottom corner (and figure colour): 8 (white)
Marks	Mark EHS Environmentally hazardous substance mark: The mark shall be in the form of a square set at an angle of 45° (diamond-shaped). The symbol (fish and tree) shall be black on white or suitable contrasting background. The minimum dimensions shall be 100 mm x 100 mm and the minimum width of the line forming the diamond shall be 2 mm. If the size of the package so requires, the dimensions/line thickness may be reduced, provided the mark remains clearly visible. Where dimensions are not specified, all features shall be in approximate proportion to those shown.
Orange plate for tanks
Detailinfo

Limited quantities	1 L
Excepted quantities	E2
Limited quantity according to 1.1.3.6	3000 kg
Detailinfo

Equipment	, Equipment: PP For each member of the crew, a pair of protective goggles, a pair of protective gloves, a protective suit and a suitable pair of protective shoes (or protective boots, if necessary). On bord tank vessels, protective boots are required in all cases.
Bulk	forbidden
Ventilation	No special ventilation required for this substance/article according to Chapter 3.2 Table A column (10).
Provisions concerning loading, unloading and carriage	none
Detailinfo

Name and description	TRICHLOROACETIC ACID SOLUTION
Type of tank vessel		Type of tank vessel C means a tank vessel intended for the carriage of liquids. The vessel shall be of the flush-deck/double-hull type with double-hull spaces, double bottoms, but without trunk. The cargo tanks may be formed by the vessel's inner hull or may be installed in the hold spaces as independent tanks.
Cargo tank design
Cargo tank type
Cargo tank equipment
Opening pressure of the pressure relief valve/ high velocity vent valve		25 kPa
Maximum degree of filling of the cargo tank		95 %
Type of sampling device
Pump room below deck permitted		yes
Temperature class		Footnote 12) This temperature class does not apply for the selection of explosion protected installations and equipment. The surface temperature of explosion protected installations and equipment shall not exceed 200 °C.
Explosion group		Footnote 7) The maximum experimental safe gap (MESG) has not been measured in accordance with a standardized determination procedure; therefore, assignment has been made to the explosion group which is considered safe.
Anti-explosion protection required		yes
Equipment required		, Equipment PP For each member of the crew, a pair of protective goggles, a pair of protective gloves, a protective suit and a suitable pair of protective shoes (or protective boots, if necessary). On bord tank vessels, protective boots are required in all cases. , ,
Number of cones/blue lights		0
Additional requirements		, Additional requirement 7 If a closed cargo tank is required to carry this substance or if the substance is carried in a closed cargo tank, the venting piping, the safety valves and the flame arresters shall be heatable. The temperature of the venting piping, safety valves and flame arresters shall be kept at least above the melting point of the substance. ,
Detailinfo